ELECTRO-ARC TAP DISINTEGRATOR
MADE IN USA "
WITH AUTOMATIC DOWNFEED, "IN-THE-QUILL"
HIGH-PRECISION "Q" DISINTEGRATOR HEAD,
3,000 LBS. PULL-MAGNET, DOUBLE CROSSARM,
20 KVA POWER RATING, AND MORE!
WOW!!
MODEL: 2DVQT S/N: 14487 NEW: 2004
CUTTING SPEEDS:
0-80 TO 10-32 .. UNDER 1 MIN.
1/4".............1 - 2 MIN.
5/16"............1-1/2 - 2.5 MIN.
3/8".............1.5 - 2.0 MIN.
1/2".............2 - 4 MIN.
5/8"............ 1.5 - 2.5 MIN.
3/4".............2.5 - 3.5 MIN.
FEATURES:
“Q” Head– top perfomer (Q/QT models) In-the-quill
disintegrator head gives continuous, reliable,
heavy-duty service for the most demanding applications.
Low-maintenance construction and design. The head
is 31 /4" diameter, hard chromed and precision
ground with .002 run-out and 9" of vertical rack
and pinion travel.
Thermal protection cutout with Operator Alert
can prevent expensive damage.
Operating Head: Head works by creating 50/60 positive
arcs per second at the target metal with a molybdenum
electrode. Provides 9” (229 mm) of rack and
pinion travel. Built-in LED current monitoring
indicator color-coded to assist operator feed control.
Operate at any angle. Can be rotated 360 degrees
around the crossarm axis. Feed scale graduated
in 1 /16” (1 mm) increments. IQ head can handle small
0-80 (1.2 mm) up to 2” (50 mm) diameter
tooling in one pass.
Automatic Feed Transistorized feed provides 9"
uninterrupted feed for hands-free operation.
Eliminates operator error, maximizes performance,
minimizes electrode usage. Features adjustable
automatic shutoff, auto stop, variable 2-speed,
feed rate selector and plug-in integrated circuit
board.
Superstructure: Column: Hard chrome plated, 23 /4” (70 mm)
diameter x 50” (1270 mm) high for a maximum working
height of 30” (762 mm) from spindle tip to table and
72” (1828 mm) to the floor. Base secured by 3 /4” (19 mm)
Tbolts allowing disintegrating head to be positioned
anywhere on the work surface. Radial Crossarms:
Two hardened 36" (914 mm) shafts 11 /2-inch (38 mm)
diameter, traveling in recirculating ball bearings.
Crossarm casting rotates 360° around column.
Separate manual locks for height and rotation and
a 12-inch (305 mm) lift rack for precise vertical
positioning.
Base: Heavy reinforced frame construction.
Overall: 31 x 317 /8” (787 x 810 mm), 34” (864 mm) high.
Ground, cast iron work top 26 x 181 /4” (660 x 464 mm).
Six 3 /4” (19 mm) “T” slots, coolant spill trough
and drain. Recessed control panel with oil-tight
lighted push buttons, low coolant level indicator
light, external fuses, and master stop push-pull switch.
Supported by four heavy-duty ball bearing casters
and machine levelers.
Built-in coolant tank: Wire mesh cartridge filter
intake. Pump: 2 GPM, 90 PSI. Motor 1 /3 HP,
single phase, 120 volt. Power coolant cable
(conducts both liquid coolant and
low-voltage current) 71 /2 ft. (2.3 m).
Machine has the following option:
3000 lb. Permanent Magnetic Base For taking
disintegration off the table.
20 KVA POWER RATING, 10 CUTTING HEAT SETTINGS
WIRED FOR 440 VOLTS/SINGLE PHASE/60 CYCLE
ELECTRICS, 50 AMPS
** INSPECT UNDER POWER IN OUR HARRISON, N.J. WAREHOUSE **
*** EXCEPTIONAL CONDITION & APPEARANCE **
** - ORIGINAL TAN/BROWN COLOR SCHEME ***